EPiC AquaFloor

High Strength, High Gloss, 2 Pack Water Based Polyurethane

Nutech AquaFloor is a High Strength Two Pack Floor Coating which provides excellent protection for Concrete, Timber, Masonry and Primed Metal surfaces with proven durability and performance. The coating provides excellent hardness and scuff resistance, designed for a wide variety of applications including commercial and industrial floors and walls.

EPiC AquaFloor is available in a clear or coloured finish.

Typical Uses

Nutech AquaFloor provides excellent protection against a range of corrosives including:

  • Petrol
  • Oil
  • Fatty Oils
  • Alkali
  • Acid
  • Efflorescence

Additional qualities include:

  • High resistance to corrosion and abrasion
  • Impervious to water and moisture
  • Ideal for interior wet areas
  • Rated for food stuffs
  • Ideal for Restaurants, Hospitals and Supermarkets.

Application & Features

Nutech AquaFloor is used for a wide variety of applications where traditional floor paints, paving paint, epoxy coatings and furniture finishes are used. It has excellent interior and exterior durability, with high resistance to solvents, corrosion and abrasion after full curing is achieved.

AquaFloor is highly petrol resistant and suitable for petrol stations and vehicle repair workshops. It is recommended for areas that require a hard wearing 2 pack coating, without the strong solvent odours of most epoxy and polyurethane coatings during application. Designed as a 2 coat system, AquaFloor provides excellent protection against fading, powdering of oxide colours, staining or marking due to contaminants, oil or grease.

Application Guide

Equipment Type

Good quality brush and roller sleeve. Spray application will depend on the type of finish required.

Do not store mixed product in spray equipment to avoid damage.

Surface Preparation

All surfaces must be free from Rust, Oil, Grease, and all other surface contamination. New concrete must have a pH level less than 10 and had at least 28 days to cure. New and old Concrete should be etched using 1 part Nu-EcoSafe Etch to 10 Parts Water. High Pressure Water Blast area (> 2000 Psi) and allow to completely dry. Painted concrete in poor condition should be stripped using our Nu Ecosafe range of paint strippers and acid etched before application.

Mixing

Mixing 4 Parts A to 1 Part B. Drill mix then leave to Stand for 10 minutes before using to allow full activation. Stirring with a stick by hand is inadequate.

Do not use after Pot Life has expired (2 hours).

Thinning

For spray application thin 10% - 15% with clean water. Do not thin for brush or roller application.

Bare concrete and masonry surfaces thin 20% - 25% for first coat application for penetration and adhesion.

Drying and Curing

AquaFloor should be touch dry and able to be recoated after 2 hours. For a full cure, allow to dry for 7 days.

Warnings

Wear Suitable Protective Coating

Wear a suitable respirator for Spray application.

Ensure there is good air flow and ventilation. Avoid contact with skin and eyes.

Safety Precautions

Sealing of smooth and sloping concrete surfaces will reduce pedestrian and vehicle safety. For greater slip reduction an Anti-Slip Additive can be mixed into the product and rolled out as a final coat. Testing is recommended before proceeding to ensure that a potential slip hazard is avoided. Refer to your Nutech specialist for alternative recommendations on steep, smooth surfaces.

EPiC AquaFloor
Quick Reference

Appearance:

Clear or Coloured Viscous Liquid

Solubility:

Water

Film Forming Temperature:

10°C

Film Thickness:

65 microns

Coats Required:

2 Coats

Recoat Time:

8 - 24 Hours

Pot Life:

2 Hours

Application Temperature:

10°C - 30°C

Coverage Rate:

8 - 10 m2/L

Properties

2K Epoxy

Suitable for Vehicles

Clear Finish

Coloured Finish

Industrial Grade

Low Odour

Non-flammable

Water Based

Related Products:

Download EPiC AquaFloor TDSDownload EPiC AquaFloor SDS Part ADownload EPiC AquaFloor SDS Part B
Important Notice

The information given in this data sheet is based on many years experience and is correct to the best of our knowledge. However as the use of our product is beyond our control we can only be responsible for the quality of our product at the time of dispatch. For additional information about specifications or application please contact our company. As this information is of a general nature we cannot assume responsibility for individual use.